新阳不锈钢
All categories
Water bilayer non-stick coating2

Water bilayer non-stick coating

Water bilayer non-stick coating, based on PTFE emulsion and FEP emulsion, is a composite coating with fine wear resistance, prominent non-stick property
Water bilayer non-stick coating2

Detail

Product description

Water bilayer non-stick coating, based on PTFE emulsion and FEP emulsion, is a composite coating with fine wear resistance, prominent non-stick property, excellent corrosion resistance and chemical proofing. It’s applicable to various requirements of non-stick pan, frying plate, baking sheet and other kitchen utensils as well as abrasion-resistant coating.

Test Items

Testing Standard & Methods

Test Results

Adhesion

10 * 10 adhesion tests every 1.5mm; 3M898 tape spreads in different directions. 
Pull 8 times, 100% non-falling as qualified.

5B

Solid content of ground coat

Take about 2g and put it into 105 degrees oven for 2 hours. The standard is 33.2% ± 2.

32.4%

Solid content of top coat

Take about 2g and put it into 105 degrees oven for 2 hours. The standard is 31.7% ± 2.

32.9%

Hardness

Mitsubishi 9800 Pencil, 1KG pencil ceremony test; FH as qualified.

1H

Ground coat viscosity

NK-2 viscosity cup test; the standard viscosity is 28 ± 3 seconds.

25

Top coat viscosity

NK-2 viscosity cup test; the standard viscosity is 23±2 seconds.

22

Acid fastness

Immersed in 5% reagent hydrochloric acid solution for 2 hours at normal temperature; no abnormality as qualified.

No abnormality

Temperature tolerance

Long-term temperature resistance of 260 degrees; short-term temperature resistance of 420 degrees for half an hour. 

No abnormality

Non-stick

Fry eggs without oil > 5

Qualified

 

The non-stick paint of this series is double-layer water-based baking varnish. The undercoat has good performance in resisting high temperature and corrosion and poses excellent adhesive force to substrate; the topcoat PTFE emulsion has good features such as non-viscidity and low friction coefficient, which is in accordance with FDA and LFDG.
Application range: aluminum, cast aluminum, stainless steel and anodized aluminum
General description of manufacturing:
1. Surface treatment: sand blasting, passivation, anodic oxidation
2. Applicable viscosity: direct spraying
3. Optimal thickness: 10-15 um for undercoat; 8-12 um for topcoat
4. Drying condition: the condition for undercoat is 90℃~100℃/6~8 minutes, spray topcoat after the surface is dry, spray topcoat after cooling down.
The condition for topcoat is 90℃~100℃/6~8 minutes, after the surface is dry under the temperature of 380℃~390℃ it takes 15-10 minutes for solidification.
5. Before use go through filtration of 100 filter screens.

Notice
1. It is generally stored in the temperature of 5~30℃ (sealed) and the storage life is 6 months.
2. Completely stir it before use at the speed of 30~40 circles per minute for half an hour. The coating should be rolled equally but no brute force is imposed to keep the coating from generating bubbles.
3.When the coating is heated to higher than 390℃ for a long time, noxious gas might be generated, so please pay attention to the ventilation of the room.
4. Due to the diversity of production environments, please ask for samples to do each test before use

 

扫二维码用手机看
未找到相应参数组,请于后台属性模板中添加
上一个
下一个

Copyright ©2021 Fulida Paint Co., Ltd.  All rights reserved     Technical Support: Starting Point Network